Elements Necessary
Two '/*" x Γ 18-gauge sterling silver sheet silver Two 7/«" sterling silver bar components Two five.three mm x three.2 mm 16-gauge sterling silver oval jump rings Two sterling silver ear wires
Applications Desired
Ruler
Marker
Jeweler's observed or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
Wonderful grit sanding pad Awl
Hard, flat surface /Îί’ drill little bit
Handheld rotary Device, flex shaft, or drill press Liver of sulfur or oxidizing solution High-quality steel wool Polishing fabric
Two pairs of chain nose pliers
one.Make use of the ruler to measure and mark two
rectangle parts of 18-gauge sterling sheet silver.
two.Utilizing a jeweler's saw or tin snips, Slice the 18-gauge sterling sheet silver into two Vi" x Γ rectangles (if you'll be earning the bracelet and pendant assignments, you may want to Slice each of the rectangle silver parts required for the opposite tasks and texture all of them at a single time).
three.Place the two W x Γ sterling silver rectangle parts on to the sticky side of the bit of masking tape. This will allow you to to carry the silver rectangles in place while you're texturing them, and can even help to maintain your fingertips at a secure length to stay away from hitting them With all the hammer.
four.Put the piece of masking tape With all the silver rectangles sticky aspect down on to a concrete block or landscape paver.
five.Which has a hammer, Carefully strike the tape-covered silver rectangles using a company strike, but You should not strike too hard. You are able to accomplish the desired texture much more effortlessly with several delicate strikes as an alternative to a few challenging strikes. Carry the tape commonly and Check out the progress from the texturing, ensuring that that your complete floor in the silver rectangles is getting a uniform texture. The area will search much like sandpaper If you're employing a concrete block. If you attain the specified texture, get rid of the silver rectangles from the masking tape.
6.the silver rectangles will have a slight curve to them, and the perimeters will be misshapen and sharp When you texture them. You'll be able to go away the silver rectangles curved or, to flatten them, spot the silver rectangles on a tough, flat surface and make use of a rawhide mallet to flatten them. If you don't have a rawhide mallet, you may place the silver rectangles on a hard, flat floor, include the items which has a thick piece of scrap leather, and make use of a hammer to Carefully faucet the leather-based covered silver rectangles to flatten them.
7.You will have to make use of a file to remove any tough or sharp edges. Utilize a fine grit sanding pad to go above the realm where men's gold & silver rings you have filed to smooth the edges and remove any file marks.
8.Evaluate from a person close of each textured silver rectangle and location a mark in the center of each bit. This is when the holes are going to be drilled to connect the soar ring and bar men's gold & silver rings elements.
9.Placed on the security glasses. Location the textured silver rectangles onto a tough, flat floor. Area the point from the awl over the mark you manufactured '/t" from your finish of the men's rings rectangle items and use a hammer to firmly strike once on the highest on the awl to create a pilot gap for drilling the holes to the silver rectangles.
ten.Utilizing a drill little bit, drill holes into Every single of the silver rectangles that has a handheld rotary silver rings for men Instrument, flex shaft, or drill push. Remember to use safety glasses.
eleven.Make use of the file or sanding pad to reduce any burs or rough edges still left from drilling holes into the silver rectangles.
12.Implement liver of sulfur or oxidizing solution for the textured silver rectangles, bar factors. and jump rings. It is essential to observe any protection recommendations the producer implies when dealing with any chemicals.
13.Soon after implementing the oxidizing Alternative, use fine steel wool to remove the darkened places about the elevated floor with the silver rectangles, leaving many of the textured spots dim. Rub the fine steel wool over the bounce rings and bar factors to eliminate some although not every one of the darkened regions. Rinse with drinking water, dry, and rub with polishing cloth.
fourteen.With two pair of chain nose pliers pointing up, hold the jump ring with the opening at the best. Roll one particular of the wrists from you and your other wrist towards you, opening the leap ring only around necessary. To shut the leap ring, keep it the exact same way and roll your wrists in the other way (imagine holding a bit of paper and tearing it). By no means pull the bounce ring ends out as this tends to weaken the steel, and it'll be hard to shut the leap ring.
fifteen.Include the bar ingredient and textured silver rectangle for the jump ring. Shut the jump ring.
sixteen.Carefully open men's gold & silver rings the loop at The underside on the ear wire, add another conclusion from the bar part. and then close the ear wire loop.
17.Repeat these techniques for the 2nd earring.